I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello Nordic team,
I am looking for an alternative method to flash the modem firmware to nrf 9160.
The issue I have with nrf connect's programmer is that it behaves unpredictably...
Question about errata workarounds for 9160 rev 1 (BO) SICA.
I see these in the errata which are relevant for our project:
[15] REGULATORS: Supply regulators default...
Hello!
The NRF52832 based Raytec Module, the Garmin NRF52 module and the Nordic Dev kits all handle the Mesh firmware I have developed without change or modification and...
Hello,
I'm trying out the Matter: Light bulb example using an nrf52840 device. So far, I have managed to build the software, flash the device, provision it into the network...
Hello Nordic Semi team,
I am porting the Modem Library to run on a different OS.
The documentation provide is great, but I have a two minor questions.
1. The documentation...
My setup:
Mac OS 11.5.2
Vs Code 1.60.2
nRF Connect SDK 1.7.0
nRF52840DK
Using the tutorial videos provided I went through the process of creating the basic blinky...
1.How exchange datas between applacation core and net core, can provide demo code？
2.How does the APP core call the API in the NET core, and how does the NET core call the...
I'm having problems using the UARTE in the nRF52840 via Zephyr. I'm watching the TX pin using a logic analyzer and seeing correct data when running at 9600 baud. But if I...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
The example provided for ble_peripheral...
Using SDK 17
There must be a way to show all commands in RTT without needing the tab to work right?
Ive been digging through the code but don't see where the magic happens...
Hi, when i'm debugging my circuit, the logical of a if or while don't work. In the image, the timeout_rtc is higher than 100, but the value of a don't change to 1. What's...
I used the P1.13 pin of NRF52833 as the output pin, and used it in the manner of the blinky sample program, but it crashed and prompted the following error message:
***...
Hello, I have a custom HOST board. There are use NRF52840 BLE chip.
I'm run Bluez 5.61 on the HOST board and by meshctl> I am able to run as a controller. But if I want...
how to set BLE_GAP_ADDR_TYPE_ANONYMOUS
i have follwoed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners...
Hi,
There are tons of documentation on how to make a mouse, keyboard or remote control work as a HOGP device, and I have successfully implemented both mouse and remote control...
