Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
We want to use a BL6554PA (based on the nRF52840) as a thread node and enable the integrated Skyworks SKY66112-11 front-end module with PA and LNA to increase our range. I...
Hi All.
Trying to complete Lesson 6 Exercise 2 from the course nRF Connect SDK Fundamentals made by the DevAcadeny, I connected the Thingy53 to my computer through USB-C...
Hi,
As part of some verification purposes, we need to test out peripheral with the nRF connect Bluetooth low energy app. We have the peripheral set to 2M, DLE enabled and...
Dear Nordic-Support and community,
I am developing a system where a Thingy91 device needs to:
Dynamically connect to a specific BLE device that sends data like Heart...
In version 2.9.0, I modified the JEDEC ID.
The system is supposed to send a "Deep power- down enter(0xB9)" command after reading the JEDEC ID.
However, after the system...
Hi,
I am trying to evaluate the provided smp_svr sample with the BLE DFU on the NRF52840 dongle after I have already tested it on the DK.
I get the following error message...
If we subscribe all attributes of cluster of device connects to coordinator will it make issue? we have noticed its dropping many values if subscribed at same time. if values...
Hi,
I'm working with a custom board build with an nrf9161, I've created my board from nrf9161dk board (change some pin and defintion), I'm able to flash and build? I can...
Hello all,
I'm working on nRF-9160 and nRF-9151.
What I want to add into SLM application were:
Configure to communicate through UART2 since it will be working with...
Hi,
I'm currently developing a headset application using the nRF5340 AUDIO DK. The thing is, I would require 2 AUDIO DKs (one for headset and one for gateway) to implement...
Hello,
I am wondering if what I am seeing is expected. I tried flashing the modem fw on the nrf9151 using nrfjprog.exe (v10.24.2); which I am able to do successfully, but...
Hello,
I have a Friend SoC with nRF52833 via SPI HCI communicating with my nodes that are nRF52833 MCUs. The nodes are LPN nodes sends data to the friend and awaits a reply...
When using the Serial Monitor, sending AT commands does not show any response from the Actinius Icarus board (nRF9160) Is there any way to resolve or debug this issue further...
Issue Description
The application starts successfully, initializes the modem library, connects to the LTE network, resolves the MQTT broker's address, and establishes an...
Hi,
Just wanted to know if nrf5340dk supports for UART baud rates until 512kbps.? And specific baud rates configuration like 122800.? If yes, is it simply configured as...
