Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Please, give me an advice. I need to measure the supply voltage and trigger an interrupt after the measurement. An END interrupt is triggered only once. It must be without...
What's the difference nrf_cloud_agps and AGPS using google SUPL data?
I'm not clear about this. README.rst doesn't explain about it.
Also, to use the nrf_cloud_agps, do...
Hi Devs,
I am facing a weird behavior with my application, where the TWI writes return NRF_ERROR_DRV_TWI_ERR_DNACK or NRF BUSY
If I ran the TWI writes from the main...
Hi Nordic,
Does SLM application support IPV6, if yes could you please point us to the AT command set which configures IPV6 and also point to us complete AT commands list...
hi ... we have done one customized board which has nRF52832 controller interfaced with WINC1500 wifi via spi communication inbuilt. I have worked with the nRF52 example program...
We need to generate MCK of more than 10 MHz to achieve I2S connection between Nordic NRF5340 and MAX9867.
However looking at the data sheet there in no configuration which...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello Nordic,
We have an NRF52840 with SDK 16.0.0 as central in our project and multiple peripherals (which are IOS or Android phones) are supposed to connect to it.
In...
Hi,
I have a custom board using nrf 52832. I am using SDK 15.2.0 and softdevice s132 v6.1.0.
I have referred following link
https://devzone.nordicsemi.com/f/nordic-q...
I have a Nordic thingy 91 connected to nRF Cloud, and I see a message "Upgrade your firmware to view Network, Sim, Device, and Service Information" I have tried to update...
The nRF9160 is connected to the nRF52840 by MCU_IF0 ~7(GPIOs) in the Nordic Thingy:91. and I know to uses UART communication between the nRF52840 and the nRF9160. Can I know...
Hi
a way to reset nRF9160 is by pulling low the nRESET pin https://infocenter.nordicsemi.com/topic/ps_nrf9160/pmureset.html?cp=2_0_0_4_0_4_1#pin_reset
During the entire...
Hello!
I would like to try the following using my nRF52840 board: press a button on the board and then receive a notification on the phone. And the other way round , press...
I am trying to update the DUT(Device Under Test) via nrf52840 Dongle with PC(ubuntu16.04/windows10) by the command as below:
nrfutil dfu ble -ic NRF52 -pkg OTA_DFU.zip ...
Hi,
This is actually a followup ticket based on this: https://devzone.nordicsemi.com/f/nordic-q-a/56228/fota-dfu-over-internet .
Now the situation is a bit more concrete...
