Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
We have a working app for SDK 16 and freeRTOS. We wanted to update to SDK 17.0.2 but after upgrading the app hangs up at the first vTaskDelay(). We use configUSE_TICKLESS_IDLE...
Hello, I am a newbie in this forum and I'm not very familiar with app development in general, however I am in the situation in which I have to develop an app to acquire ANT...
Hello Nordic Team,
I am having issues with the HCI UART firmware for the nRF52840 on the Thingy91. I have been using the HCI UART firmware from nRF Connect SDK 1.0.0 for...
Hi, I am working on a project to send commands from mobile to device and vice versa. I am using nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_template . I have made...
Hello,
I am using : SDK 17.0.2 and S132_7.2.0 with nrf52832 DK
in my BLE application, the FDS has 2 behaviors :
1) When the softdevice is enabled : fds_write returns...
Hello,
I´m searching some information about the NB-IoT protocol stack and the overhead which is send with every message.
I nearly searched the whole net but didn't find...
Hi,
It has been stated that nRF9160 doesn't support RLC UNACK, which we have also observed with nRF9160-DK in signalling mode against radio communication tester. Are there...
Hi,
I have a setup where mobile device(central) connect to nrf51dk (peripheral) and exchange data for a time. I want to detect unplanned disconnection of mobile device in...
Hi all, I try read DEVICEID in non-secure application but always return "BUS FAULT", I tried too enable NRF_FICR register in "spm.c" but the error persist!
I try
NRF_FICR_S...
Good morning Nordic,
I am trying to configure the I2C pins for our board (using nRF5340-QKAA SoC) but I cannot find the pin numbers for I2C_SDA and I2C_SCL.
All I could...
Hi all,
We are using the BMD-340 from uBlox, which runs the nRF52840 SoC.
On this BLE Peripheral, we are running the ble peripheral demo project ble_app_uart (pca10056...
