Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in " nRF5_SDK_15.3.0_59ac345 " as following:
A custom...
I am working on BLE mesh network,initially I have tested the light switch demo example it is working fine.Now I want to test relay functionality by using light switch example...
Hello everybody,
I have two nRF51822. One of them is connected to MCU (STM32 Development Board Nucleo 32) via USART with 115200 baudrate. The other one is connected to USB...
I'm having issues trying to program a custom board with NRF52832_QFAB in DC/DC config. I couldn't reach a complete programming getting error in open ocd with two programmers...
I'm looking for the NRF52840 hardware reference designs. Most of the links I saw seems broken. I'm particularly interested on the minimum components used as I'm looking at...
i am testing nrf power consumption using amper testing method and example which i am using was ble_app_uart. i modified the example by adding app_timer and removed sleep,...
i want to sample 2 ADC channels value and send to smartphone, and my thought is use the software time to sample 2 ADC channels every 500ms, the code is like this below. void...
Hi,
I am trying to toggle an LED in bootloader, adding nrf_gpio_cfg_output/write has no effect to the code. The code compiles without errors but doesnt seem to be executed...
So I have been using your chipsets for a little while now and love using Nordic products. The GPIO are super easy to use with your drivers and there isn't 18 million sleep...
Hi,
I want to make a bluetooth mesh system with over 400 bluetooth devices. As I know the Nrf52840 Dongle can connect to 20 devices concurrently, so if I use 20 Nrf52840...
Hi
Am trying to establish nrf52 DK as peripheral with nRF connect application as central but am unable to establish connection between both.
Please debug the following...
I've been using the CLI and also piping NRF_Log thru the same backend. In my application there are alot of time critical operations. I've noticed with some GPIO toggling for...
We have a device with firmware based on 14.2 (with sd-id 0x96) and we're trying to do a DFU over BLE to a firmware base on 15.2 (with sd-id 0xAE).
We can do a firmware update...
Hello:
I've got a application where I want to detect if the NRF52 is near a NFC reader. I don't need two way communications, but it would be good if the reader could modulate...
