Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Dears,
I have nRF9160-DK and nRF51-DK(PCA10028).
I have used nRFgo Studio with nRF51-DK(PCA10028) to firmware download.
And I have used nRF Connect - Bluetooth Low...
Hi.
How could I set extended advertising through the 37 secondary channels as default, in an nRF52840 module which is using PHY_CODED modulation and running a ble_app_uart...
When working on adapting the bootloader for NRF52832_XXAB I noticed that -DNRF52 seems to define NRF52832_XXAA and later defining -DNRF52832_XXAB does not override it. I suppose...
If the Mesh DFU process fails (maybe a packet gets dropped or something), what happens? Will the device get stuck in an unknown state? What does the recovery process look...
I am trying to make the nrf9160 device work with our own AWS IoT account.
The nrf9160 device succeeds to run mqtt_client_tls_connect(). Then it runs mqtt_client_tls_write...
Hello,
I am using SDK12.3 and have problem with garbage collection (FDS module).
My apllication depends on timeslot, so that FDS is supposed to run together with Bluetooth...
Hi
I am writing ANT+ device on pStorage and want to read back from memory during ANT+ stack init. I am trying to change the Device name on this snippet
No luck so...
Hi,
I'm working on the ble_att_mtu_throughput example code on nrf52840(peripheral) & nrf52832(central) . SPI data is transmitting from TI(slave) board to nrf52840(master...
Hi there! I am developing a device with the nRF52810 that requires the following:
Receive audio over BLE
Store audio in memory
Playback audio on command
Would...
SDK 15.2 API 6.10 SES custom board
I am trying to get DFU to work and it is not seeming to work right.
I am trying to engage DFU mode by holding in button on board for...
Dear DevZonee's
Im trying to esablish a BLE connection using the following configuration of the peer-manager:
* LESC
* Just Works -> IO-Caps none (0x03)
If i run...
Hello
I am using SDK12.3 on nRF51822 chip using Keil V5 on windows 10.
I am using experimental_ble_app_buttonless_dfu example and bootloader_secure example.
They both...
Hello!
SDK 15.3
If I build secure_bootloader example project using Segger Embedded Studio it works, I can see it nRF connect.
If I build it using armgcc it does not...
Is there any actual difference between "Fast Advertising", and "Slow Advertising" - or is it just a way to easily specify two different sets of timing parameters?
The question...
Hi,
I'm having problems with the bootloader in SDK 15.2. I'm using an NRF52840, I don't know if the CryptoCell is giving me issues.
The DFU fails when checking the FW...
