I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
We are encountering a problem when we try to avail Nordic UART service (NUS) and Mesh service in one application. The problem statement is that after Provisioning, when...
Dear Team,
We are working on nRF52832 BLE MCU. SDK version = 15.0.0. SOFTDEVICE version = 6.0.0. IDE = segger embedded studio.
In our application we required software...
Hi,
I have read this thread Notification_Loss but could not understand my problem.
On peripheral side, I am making sure that error events are properly handled while doing...
Hi,
I'm working on an application for the nRF9160 using the nRF Connect SDK. I want to integrate this app into our build system and thus would like to be able to build...
Hi,
we have to stick to SDK 14.2 because our project is close to finish and we use C++ which is not good supported be SDK <15 due to the macros.
But still we would like...
Hello, I am trying to adapt open thread coap example to use with the PCA10059/NRF52840 Dongle board. I am using segger IDE. I adapted the CLI to use the USB like in the thread_cli_usb_bootloader...
Hi all,
i want to read the power (WATTS) value and send it to ble. i have attached datasheet also. i want to know how to trasmit COMMAND e.g 0x58 through UART. any api...
SDK 15.2 SD API 6.1 SES I am trying to get my system to work on a DFU system. In order to do it i need to have a secure bootloader.
using the secure bootloader in the example...
Is there a way to configure the nRF51822 to support writewithoutResponse? I'm using the Adafruit Feather 32u4 with the nRF51822 ble chip. My iOS app works fine with the older...
Hi
I plan to use nRF52832 based nodes with an accelerometer sensor which generates data at a rate of 468 bytes per second. For evaluation, I have two nRF-52 DK evaluation...
1. I read the Configuring DFU over Mesh & nrfutil User Guide , but still do not know how to test this example.
2.is we must need 2 devices, A connenct to PC for nrfutil...
hi ,everyone
HOW TO do a DFU by myself serial protocol in mesh network ?
0.I know it can scucess through a python script in PC (even thougth i try failed to run this example...
Hello,
I want to develop a ANT+ product, example rope skipping or Dumbbell, but i can not find out these ANT+ Device Profile.
How can i do? Can i use a personal ANT+ Protocol...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
