Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
Hi! I am trying to read the voltage of a LiPo battery as explained in this blog post. The code on github however, is not compatible with the latest SDK for the SOC (12.3)...
Hey guys,
we are currently evaluating the pc-ble-driver-js. We want to get it running on a Raspberry Pi 3.
The Nordic nRF52840 module was flashed with SD Version 6.1.0...
Hi,
i am using nrf51822 interface with mpu9250 and i want to detect a tap without using of DMP feature of mpu motion sensor. my application requirement is low current consumption...
Hi,
sending some data from nRF52840 (DK or dongle) to a host computer via USB. When nRF52840 is connected to a "powerfull" host, all goes ok; when connecting to a "less...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
hello,
Now i transplant pwm_library programming to ble_app_uart_c(central) in SDK15.0.
But i found the program cann't run in NRF52 DK.
I found it build no errors but...
Hello,
We are evaluating now a new project and I am struggling to get a feeling about one moment of Thread network and its particular implementation with nRF52840.
In...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
Hi,
I'm using SDK 13.1, SoftDevice 4.0.5 on nRF52832. I have an app which runs for a long time but will occasionally enter the hardfault handler from an address within the...
Hello,
I try to send multi notification in one connection interval, but I can only send one notification.
Hardware
Peripheral: nrf52832 costumed board (with BMD-300...
Hi,
I'm using nrf52 custom board designed for our project,For this we have P0.09 and P0.10 as rx and tx used for uart, when i configured this two pins as rx and tx it is...
