Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
Hello. How can I send binary data (in order to not convert it to ASCII string) over UART?
I have sensor data (obtained over BLE). Every measurement is 13 bytes, sample frequency...
Good day!
Thank you for your consideration of my problem! The system is an nRF52832 utilized as a motor driver of a small 2W high rpm maxon motor. The system performs as...
Hello,
I am trying to evaluate the nRF52 dev kit. The "getting started" HTML documentation has a link for "Setting up the development kit". This links loads "Oops (400)...
Despite all the questions on this forum for how to change PWM frequency on the fly, I found no mention of anyone using "WaveForm" mode. Perhaps it's new? There are also no...
Dear all
I have a service with an UUID. Let's say 11111111-2222-3333-4444-555555555555
I also have two characteristics that belong to this service:
66666666-7777...
I am using an nRF52 DK to build a prototype for a product. The device needs to have a connectable advertisement (as peripheral with multiples connections possible) and at...
Hello, thanks for reviewing this. I am trying to install and run Zephyr on the nRF52840 module that is on-board the nRF91 DK board. I have gone through the setup process and...
I'm doing this:
1. Start a scan, with these parameters:
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */ #define SCAN_WINDOW...
Hi
We are evaluating the nRF52832 for use in a medical application, I have modified the example ble_app_cgms_pca10040 to drive our evaluation hw. We are using the Nordic...
I am trying to interface nRF52-DK (PCA10040) with an external MCU (PIC24FJ128GC010) using UART. When trying out the ble_app_uart example in the SDK version nRF5_SDK_15.2.0_9412b96...
