At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I am using nrf_fstorage_sd which uses nrf_atfifo. I would like to know what it is max usage of m_fifo queue so I can set lowest NRF_FSTORAGE_SD_QUEUE_SIZE value. I figured...
I develop an program with BLE DFU support, but we hope to merge all hex as single hex file. Then we can burn this hex file by programer (such as jlink or NRF52DK), So we have...
Hello,
I'm trying to run the s132 (and s140) softdevice while running a proprietary mesh network stack. Naturally I'm requesting a hefty amount of radio slots. I need to...
Dear Nordic,
I have an application which contain UART and BLE advertising. For power consumption i use enable disable UART.
Enable and Disable Uart:-
Is it right way...
hi..
i am using nrf52832 and a peripheral device .. temperature sensor ,my temperature values are increasing like(0 ,27,75,80...) how to get a approximate value .
i have...
Platform: nRF52832 using SDK12.2 and Keil 5.20a
I've encountered strange corner case when displaying negative floats using NRF_LOG_DEBUG .
My test code looks like this...
I want to use BLE 4.2 Data length extension to stuff more data into one packet. I am looking at the "ble_app_att_mtu_throughput" example and am getting confused because there...
Hi!!
I am sending data by BLE data received by SPI.
The interval for sending data at BLE is 64 ms.
I have written and run NRF_SPI 1 -> ENABLE = 0; and NRF_SPI 1 -> ENABLE...
can't open 'J:/Projects/..../Electronics/SDK/BT840F/nRF5SDK15209412b96/nRF5_SDK_15.2.0_9412b96/examples/ble_central_and_peripheral/experimental/ble_app_att_mtu_throughput...
If there are multiple beacons, let's say B1,B2,B3,B4,B5 and a BLE receiver. I want receiver to only wake up from sleep mode when B1 transmits(long broadcast interval) and...
Hello Nordic community,
is it possible to configure the network key, application key, node address with the help of a byte array? The keys, adresses and all the peripheral...
I can not transplant SDK15.2's ble_nus into my project, there is no errors after i complie it, but when it does not work, I use RTT to see the errors, like this:
line...
