Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
Hi,
we are testing nrf52840 together with rfx2411n amplifier to extend the range.
The problem is that we have same range and same RSI values when testing with bypass mode...
Good afternoon,
I have purchased multiple nRF52840 Dongles and so far have successfully ran blinky peripheral and master (required to adopt PCA10056) examples.
I tried...
Hello Nordic
I am testing SEGGER EMBEDDED STUDIO and I think it is little buggy.
When i simulate NRF52 application without actual device (I can not
debug on hardware...
Hi,
I used SDK_15.1.0, secure_bootloader/pca10040e_uart.
Through PC uart,it update successfully .But boot through android(linux) uart,it returned 'invalid crc'.Can anybody...
Hello,
I am working on BLE Peripheral and Central part on SDK11 for a long while. Now i want to start with NFC.
I tried to go through nfc section in SDK14 but could not...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
i am using ubuntu 16.04
using eclipse photon IDE
nrf52_14.1.0 i am unable to run to run more than two threads can u please help me out in this
i am trying "nRF5_SDK_14...
Hi,
I am working with bonding process on Android App.
My problem is:
When I create bond to nrf51822, the process complete successfully. Then after a few seconds (3-5...
Dear Nordic Team,
Thanks for supporting .
I have a custom hardware for nRF52832 its working for nrf_beacon example but its not work with eddystone beacon example.
please...
We’re working with the NRF52, SDK 14.2 and SES.
Somehow we have managed to have our boot loader extend into our MBR params page. We extended the stock SDK 14.2 boot loader...
So using the above code I am trying to set the threshold of 2.3 volts on the power comparator. I am using sdk12.1 with Soft device 3.0.0 on an nrf52832
I keep getting NRF_ERROR_SOC_POWER_POF_THRESHOLD_UNKNOWN...
board nrf52840
sdk 15.2
hi i have one problem in connection, once i connected the device and disconnect means ,the device stops advertising..if i reset means it will show...
