I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
I connected up +5v to the external power pins of the nRF52dk. I see +5 at TP14.
When I set the power switch to 'on', the board does not boot.
Is there something else...
Hi:
Looking in both SDK12/13 I cannot see any examples related to an HID Joystick/Gamepad.
It looks like somebody asked a similar question here: devzone.nordicsemi.com...
I am using nrf51822(pca10028)
i used the timeslot API tutorial in devzone..and it worked fine but i want to integrate the radio receiver example along with this.
nrf_radio_signal_callback_return_param_t...
Hi
In the SDK13 release notes and even in a few posts in the DevZone the new S140 5.0.0 Alpha2 Release is mentioned. I looked for the download link in the product page...
Hi all
I'm using the GATT server on the nRF51822 with the SoftDevice S130 V2.0.1. I've implemented a service and a characteristic which supports only write requests (including...
Here is my question.
I always disable uart after I send data.
NRF_UART0->TASKS_STOPTX = 1;
NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
this was write in the...
Is there a compiler/makefile flag that allows for 64bit printing?
I have included inttypes.h, and tried both %llu and "PRI64" as shown:
char scrbuf[30];
uint64_t time_alive...
Hi
We are using NRF52 and SDK 11 and S132.
The nrf52 acts as a central and selectively connects to the closest phones (ios) that are acting as a pheripheral.
For this...
hello,
nordic's engineers, need your help.
(1) the first problem : can not set VDD output to 3.3V
From nRF52840_Product_Specification_v0.5, it says:
High voltage mode...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm using nRF chip as Multi-connection Central and 1 Peripheral as well.
My event function is
static void on_ble_evt...
I've tried everything I can find on this topic and I still cannot get P0.09 to behave as a GPIO pin. Does it have something to do with the way I'm attempting to initialize...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
