I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello,
i decided i will use a nrf52 3rd party module for my project cause i want to skip Qualification Process and Bluetooth RF-PHY test.
I haven't seen any 3rd Party...
nrf52DK - SDK12.2
This is probably a simple thing I am missing but I can't seem to find the answer.
I have been following the tutorial for BLE Characteristics ( here...
Hi,
I am working with a nrf51822 and I have seen that the way to wake up from System Off mode is by a GPIO interrupt. I wanted to know if it is needed to configure previously...
I am a new to the uVision4 and having trouble with the 51822 evaluation kit demo.
I am able to build the ble_app_hrs demo and can load and run it using the Flash / Load...
Hi
I'm using fs_storage function to read and write in flash memory. Value successfully stored in evt->store.p_data but after power off it value become 0
switch(evt-...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
Hello,
i use a nrf52 developpment board, with the SDK 12.1.0. I use the ADC example which use the ppi channel, my question is : it's possible to set the ADC driver without...
Hi all,
i try to log event in memory, and when connection is established read value from E2C and send to APP.
if i send characteristics when event BLE_GAP_EVT_CONNECTED...
I use the ble_app_proximity example of the nRF51_SDK_10.0.0_dc26b5e, the chip on my board is QFAAH00 . When I down load the code, it pops the windows "IAR Warning: Stack pointer...
I am learning BLE and trying to develop a Health Thermometer which can be seen in the nRF Toolbox
I am using Bluetooth Developer Studio but cannot get the nRF Health thermometer...
In SDK 11.0 it seems that in case pin 31 is configured as a button (using port events), nrf_gpiote_task_enable keeps triggering the port event due too a work around for OUTINIT...
I developing wearable product based on nrf52832. The product is act as a beacon and its location track by other fixed BLE readers to positioning it in particular defined area...
Hi,
I'm working on accelerometer + BLE application. My current configurations are nrf51822 and LIS3dh accelerometer chip, Protocol TWI, Softdevice 110, BLE service type...
Hi!
I'm trying to learn osTimerStart(), \ble_app_hrs_rtx.
Compiling was successful, and it is working.
If I set the timer interval shorter than 25 ms, the timer cycle becomes...
