We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
Could someone advice how the Zephyr I2S (i2s_nrfx.c) modules or Nordic Module (nrfx_i2s.c) should be used to I2S TX a USB ISOCH stream (1msec), when the 2 rates ...
Hi,
The project is based on nrf cloud reset FOTA sample, ncs 2.6.1, testing on nrf9160DK. I use a FT232 to monitor the output from uart2.
I want:
uart0: used for outputting...
Hi, I just started working on nrf5340 and on importing the blinky sample, i got an warning regarding my gpio driver files. i have tried reinstalling my SDK and it doesnt work...
I am using the following chip: NRF52840-QIAA-R
boggi@getshop-boggi:~/....$ nrfjprog --program /home/boggi/..../build_1/zephyr/zephyr.hex --sectoranduicrerase --verify...
Hello,
I want to program the NRF52840 chip via the nRF Conect for Desktop application using the NRF52840-DK. I made the connections as in the image and I also made the NRF52840...
Hello All,
I am having issues using the Async zephyr API to control the UART. I am using the Seeed studio xiao nrf52480 sense board.
I have followed a couple of nordic...
Is it possible to use the nrfjprog utility to program and secure (from read over the SWD) the nRF52840 in one step? I tried:
nrfjprog -f NRF52 --program abc.hex --chiperase...
Hi,
I'm running into a strange issue with an application based on the azure_iot_hub sample using ncs v2.5.0 running on the nRF9160DK. Everything works fine when I run the...
i want to use NRF Hardware Timer into Zephyr OS(NRF Connect SDK) . How I can use any example or Suggestion Please. My Issue Is I have to trigger ADC Read Every 1ms . so Zephyr...
Hai
We are already using nrf52820 for various projects and already having stock of around 10k.
Now we are planning to work on Bluetooth mesh. I found NRF52820 will support...
Hi,
I want to run the radio_test sample on a custom board, how do I go about doing this?
The custom board uses a UBLOX NINA B401- which utilises the nRF52833 chip...
I have created the sample_fs project from subsys/fs/sample_fs. I have not made any changes to the project. I have built it and flashed it onto a nrf52840dk. But I'm getting...
Hi,
I want to enabe filessytem, diskaccess and sdmmc on nrf5340 in order to save data on a SDCARD via SPI.
I have added the following to my proj.conf
CONFIG_DISK_ACCESS...
I posted a question in the following link, but there is no answer.
https://devzone.nordicsemi.com/f/nordic-q-a/114929/please-tell-me-the-scroll-up-down-command-for-mouse...
