I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Dear Nordic, Could you please advise how to interpret the version in this context? The modem firmware v2.X - is it the version that does not exist right now? If yes, when...
Hi everyone,
I'm working on a project where I have four sensors connected to my chip via two SPI buses ( 2 on each with 4 CS). My goal is to read data from these sensors...
I am using an nrf528232 based BLE module, the Taiyo Yuden EYSHSNZWZ: https://www.digikey.com/en/products/detail/kaga-fei-america-inc/EYSHSNZWZ/7104534
Running BLE and uart...
Hello,
I have recently attempted to port over to the latest v2.7.0 of the SDK by following the steps in the latest getting started guide for the L15. I have been able to...
There is this post from three years ago here that mentioned LLPM isn't supported on nRF5340. The answers had mentioned some issues with LLPM on the network core & that the...
NCS v2.6.0, NRF5340dk
I'm trying to configure a project that uses mcuboot with direct XIP with the external QSPI flash. I've been looking at examples in
ncs/v2.6.0/nrf...
Hi! We use Npm1100 SHPACT on GPIO and want to ask connect SHPHLD directly to VBAT.
The spec has 100kOhm resistor between SHPACT and VBAT.
However, we don't use the button...
HI
softdvice : s132
SDK version : nRF5_SDK_17.1.0_ddde560
I am using the nrf_delay_us() function. The product I am using now controls the gpio in us units. Since it...
Hi,
In NCS 2.0, the ability to add a custom child image was added. This works fine but as soon as you include the mcuboot child image, the order of the child image builds...
Hello folks!
Today, I have what I hope is a really easy fix that I just can't find the answer to.
I would like to transition from using the nRF Connect extension "build...
Hi,
First of all I would like to know when the Nordic SDK will be based on Zephyr 3.7.0, which is an LTS version.
Secondly I would like to find an easy way to find out...
looking at https://github.com/nrfconnect/sdk-nrf/tree/main/lib/location
specifically https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/cloud_service/cloud_service...
Hi, I am working on a project using the nRF52832 and the nRF5 SDK 17.1.0. We have a sensor with non linear behaviour and in our attempt to linearize it we found an article...
