After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
board : nrf5340 sdk : nrf-connect v2.1.2
Hi. I am studying OpenAmp and RPMSG using NRF5340DK board.
I looked at the examples below for studing OpenAmp and RPMSG.
C...
nRF Connect SDK 2.2.0 on Windows 10 pro, I have a nrf52840-DK and a nrf9160-DK. I would like to test a simple OpenThread CLI application
I have the following prj.conf
...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
I am a beginner, and there is no problem with scanning and receiving data in RTT Viewer. I am currently stuck on how to use CDC ACM US. i have notice there are example on...
I am interfacing with a part that uses the same pin, P0.6, for two purposes:
1) The pin is used for UART communication. MCU RX input.
2) The pin is used as a GPIO. MCU...
Hi Everyone,
I have a custom board with a nRF9160. I have updated the firmware to 1.3.3. I am using SDK 1.9.1. I found that the board works well with the GNSS sample from...
Hi, I have an application where I need a latency below 100µs between transmission and reception over the air of a 32 bits payload.
We are currently evaluating the ESB protocol...
May I know if developing using the example of proprietary_rf that does not use BLE in SDK is also subject to a user fee? (If there is a usage fee, I would like to know the...
Hello,
I have an issue with BLE-Mesh, wherein If I provision a device and then flash the board with a new image (I do not erase and flash), the device name & provisioning...
Hi all,
we are using UART uart_rx_enable() to define a timeout of 500. Most of the time, event UART_RX_RDY is raised as it should be after a timeout. If, for example, we...
Hi!
Which is the right way to install nrfconnect SDK for VS Code for linux? Is it automatically or manually as described in the documentation?
Regards.
Hello all, I hope you are doing well.
I Have a project on NRF52840 in which I have multiple sensors connected to the NRF52 and the sensor data are storing in the SD card...
I have received a development kit from Farnell. It has version 3.0.0. When I connect an external target, I can't get a connection. It only recognises the onboard chip. An...
Hi there,
I would like to use SMP for DFU my Firmware and communicate with other SoC by one UART port. And then, in SMP protocol specification,I saw there is an ID (64)...
Hi,
I got a new nRF52DK, started working with it. After Blinky example, I tried UART example.
UART program is working fine. But Now i can't reprogram DK.
I tried to...
