first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hello,
we are currently developing an MQTT Bridge Application. We plan to use a nrf52840 in combination with the nrf9160 as our Bridge which is going to send its data...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
I have developed my thread application based on nrf_sdk_for_thread_and_zigbee and implemented DFU OTA in my application. It is working fine with no issues.
I am using nrf52840...
Hi,
My nrf52840 is not detecting the USB, i tried by pressing the SW5 after that bootloader led starts blinking but not showing any drive in the PC also
can you please...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I have an applications that was using NCS 1.7.1 in its west manifest. I am going through the process of upgrading to 1.9.1
My application using zero latency IRQs and sets...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
I am trying to interface the Grove 4 Digit Display(TM1637) with the nRF52840 DK.I have successfully interfaced it with ESP32 and get clear output after researching for the...
The main loop in our nRF9160 (NCS v1.8.0) is a typical main loop with semaphore following https://docs.zephyrproject.org/latest/kernel/services/threads/system_threads.html...
Hi
I attempted to create a 32.768 kHz signal from the nRF52840. When I use the HF external clock: NRF_CLOCK->TASKS_HFCLKSTART = 1 ; the generated clock signal looks great...
Hello,
I am waking nRF52805 up from SYSOFF by an accelerometer, after which I want to wait for a second and then start advertising for a short period.
All is working fine...
Dear Nordic,
Could you please suggest and and expamle or advice how to use in-project libraries properly (not 'externally built' as an know example shows). It's better to...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Is there a limitation for number of INT's If is how do I attach same interrupt on multiple buttons
for(..my buttons){ ...
ret = gpio_pin_interrupt_configure_dt(pb, GPIO_INT_EDGE_TO_ACTIVE...
I want to change the connection params in peripheral role with nrf52840 without informing the central device to do the actual setting operation, yet I don't find a relevant...
