first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
I performed early software development on an nRF52840-DK. I'm using Zephyr on the nRF52840.
Now I have a custom board and started doing development on it by creating a ...
Hi Nordic experts,
Recently, I tested and found that I failed to start the advertisement with NCS 1.7.0 if the length of advertising data is greater than 251 Bytes, for...
Dear sir/madame
Start & stop of advertising and how to prevent automatically restart of advertising in case of a random disconnection or disconnection initiated from the...
Hi,
I've been scowering the SDK dicumentation and DevZone for this information without finding it. My apologies if this has been answered before.
When using the SUPL library...
Hello!
is it possible to execute some code in the section
or do i have to implement some kind of thread logic? or any kind of nonRTOS library?
I come from FreeRTOS development...
Hello,
The Example code is running, but only printF() statements are printing and to the PC terminal program.
The example calls for softdevice build 122.
I "think...
Hello,
I am working with the Thingy91 device and the SDK v1.3.0 asset tracker example (I am not interested in upgrading at the moment). I would like to know how I can save...
I flashed my board with DTM image, assign P0.20 for TX and P022 for RX. Most of the times the DTM application can't communicate with the nRF5340, maybe 1 out of 20 times,...
Hello,
I used to import our current project to segger embedded studio v5.62 from keil so I'm followed these instruction .
All project files are compiled well but problems...
On the nrf52840 module, when I first output to one of the GPIO pins when I load any softdevice ble_peripheral instance I have installed. 10 ms after the VDD pin is energized...
Hi,
I have nRF52840 DK, and PPKI power profiler, I measured peak current mA using PPK on Radio Transmitter, And I found there is a big discrepancy between measure and typical...
Hi Guys,
We are currently working on a mesh sensor network. I have already developed a vendor sensor model (client and server). The client will also work as a gateway and...
I have a couple of questions regarding the nRF52840 internal voltage regulators, specifically REG0. I couldn't find the answers from the datasheet and therefore I hope that...
I started using nRF Connect for VSCode a couple of days ago on one computer and it has been working great. Now I had to switch to a new computer where I had also just briefly...
The first chip silkscreen for 2050ST second chip silkscreen is 2109XN third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
