Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hello,
I am having difficulties reading the ICCID of a solder sim that is connected to a B1 revision of the NRF9160. I have tried two different NRF9160s, two different solder...
We're getting this strange AppError that is supposedly coming from the SD (considering the PC is correct)
App error: id: 0x00000001, pc: 0x0001505C, code: 0x00000715
I...
It looks like the DK comes with a coin cell type battery and there seems to be a tab that can be pulled off to activate. Can someone explain how to switch into battery mode...
Hi,
Which BLE dongle can we use on PC in order to communicate with nRF52810 and nRF52832 chips?
Is there a desktop version of "nRF uart app" for reading and writing...
Hi all!
I want to run OTA DFU over Thread from a RPi3. Previous tests from a PC were successful.
I installed nrftuil: sudo pip3 install nrfutil==5.2.0
I added the...
Hello.
I am wanting to send an infrared signal from my nrf52 DK (pca10040). I've found code online for sending custom IR signals using pwm and a gpio pin. The IR signals...
Hi! We're developing an app which connects to BLE devices for different purposes. We've successfully enabled MITM using windows(an example from Microsoft) , but are having...
Hey, I'm trying to install the cat tracker application. When I'm executing the npm ci command. It is prompting the following error
ubuntu@ip-172-31-25-55:~/aws/nrf-asset...
I am trying to code a cycle power service and I need to add a server characteristic configuration descriptor. This service is probably the only BT SIG service that uses that...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
