Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
I can't get a button to work on a custom board; but same firmware HEX file on a different board works fine.
Using nRF5 SDK 17.0.2, SoftDevice S132 v7.2.0.
using a custom_board...
Hi,
I'm using an nRF52840 and I need to implement a driver in c for an external chip. The c driver is written, and I only need to add specific functions regarding the SPI...
I can't see the answer, so I will write it again.
hello.
nrf24l01p(ptx), nrf51822(prx)
nrf24l01p set
TX_ADDR = 0xA5B300
EN_AA = 0
EN_RXADDR = 1
SETUP_AW =...
Hi, I am trying to add Buttonless DFU functionality to the ble_app_blinky example.
The process I took
1. added the following files to the project
ble_dfu.c ble_dfu_bonded...
Hello, I am trying to implement a basic BLE connection between the nRF52840 Dongle and an Android Device (nRF Connect). I wanted to secure this BLE connection with a passphrase...
Hi everyone,
I am working on buttonless OTA DFU. I have generated my own private and public keys using nrfutil and created the .zip file for DFU.
While generating the...
Using the following image UUID on NRF51822, how do i connect to the host in the nRF5_SDK_12.1.0_0d23e2a softdevice? I used to the example of ..\ble_peripheral\ble_app_uart...
Hi,
I used one nRF52840 dongle and one DK, and placed one sniffer in between to caputure the packets.
The connection interval was set at 7.5 msec, GAP event length is...
I have gone through the nWP-034 document (nRF9160 Hardware Verification Guidelines) and wonder if it exist sample code (firmware) to be used, as a baseline, during regression...
Hi,
we have interfaced Accelerometer Module with NRF52832 using SPI Communication. Psuedo code of code snippet is :
<<Place the snippet here>> Expected : After nrf_spi_transfer...
Hi,
I am trying to use APP_TIMER to detect if a sensor isn't responding to I2C Commands. I created and started the timer with the following steps. The project is based...
I'm using an ISP1807 at 1.8v in a very space constrained and power constrained device.
Is it ok to connect unused pins to GND to make routing easier?
Pins 3, 5, 8, 10...
H,
I am using the SDK 15.0.0 and Segger Embedded Studio for ARM V3.40.
I have been successfully defining a flash memory section for data exchange between the bootloader...
Hi,
I would like to enable the RAI support in the latest master branch of nRF.
Therefore I had a look at the kconfig reference:
https://developer.nordicsemi.com/nRF_Connect_SDK...
