Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I hope this isn't a duplicate of another question. I searched on sd_power_system_off and didn't see anything exactly like this.
I'm creating a new project, based on ble_app_template...
I have the 51822 chips, and want to establish a network with large data volume, I use the S130 now, but the effect is not ideal, so I want try the BLE4.2. Do we have the SoftDevice...
Hi,
For the past few weeks I've been trying to make a small device that would simulate a mouse with Arduino and MPU6050 accelerator + gyroscope sensor. I wanted the device...
created a new BSP PCA10001 from PCA10028 and replaced the CFLAGS += _DBOARD_PCA10001 for uart example in peripheral folder using sdk 10.
Migrated simple_uart example &...
Hello,
I wish to communicate with the chip via SPI NRF51822.
The NRF chip is configured as a slave. Based on the SPi_slave_example code, I can't set to 1 the semaphore...
I configured my system to sleep after inactivity time.
nrf_gpio_cfg_sense_input(WAKE_UP, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_HIGH);
err_code = sd_power_system_off...
NRF51822 most time is in sleep mode.
Each 5 seconds it wakes up to make ADC measurements.
But adc_event_handler force only once, but I want to see it every 5 seconds.
...
I'm new to using the RTT Viewer. It was working fine (all morning). I've only been using the SEGGER_RTT_printf(0, "string %d \n",x); call to dump text and data to the viewer...
Hi,
We are using the BLE keyboard example as a basis for a design and notice strange behavior.
Only change was to create a custom_board.h header for a button press on...
Hi,
I can use the DFU bootloader via HCI/UART to update the application image.
Reference DFU init pakcet . The init packet contains a 4-byte value identifying the version...
I searched the database but did not find an answer to my question.
My environment is as follows:
Keil uVision v5.18a
Nordic SDK 11
nRF52 PCA10040
Softdevice S132
...
Hello,
I am trying to write data to flash. I did successful write data to flash, but I need delays between erases and writes. I tried to avoid the delays with the NRF_EVT_FLASH_OPERATION_SUCCESS...
Hello,
I am currently using Renesas RL78 BLE chip and the UAP & NAP address is as follows 42-00-DE.
Now, for better performance, I migrated to Nordic nRF51422 and am...
Hi all,
I have to transfer a lot of data over the UART channel, and run into some problems...
First problem was/is the UART FIFO Size.
There are three different defines...
