Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
brief:
The Zigbee version fo the example was ported to matter. Both standards use ZAP files for the definitions, but have smaller differences in their specification. The...
Hello, I am aiming to compile a project with SES studio, version 6.40 . The target is nRF52dk. I have the following issue: 1.\
Generating linker script ‘SmartShelfPusher...
Hello everyone,
So I'm trying to build for a custom nRF9160 board. I've copied the Thingy:91 board and renamed all files and edited the cmake , as per the guide and video...
I'm trying to run the Hello World example in VS Code. When I launch the IDE, I can see that there is an error "No Kit Selected". When I attempt to install a Kit and hit the...
Hello.
I'm trying to connect to nordic device, but only connects randomly.
The logs of Android in attachment.
Android version: 11
The java code:
The...
Hi guys,
I'm working to test how much performance I can get out of the mesh implementation. I'm using the BT_MESH_MODEL_ID_SENSOR_SRV ID to create a custom model type, and...
Hi,
We have an application scanning 4 ADC inputs AN1, AN5, AN6 and AN7
We setup the SSADC in scanning mode:
We start sampling the ADC on a regular basis using PPI...
Hi,
I'm using a custom nrf52832 board (picture below), and I'm using nRF Connect SDK in visual code studio. I'm new to nRF so I'm a little confused about programming custom...
Dear Nordic,
We are developing nRF21540 + nRF5340 solution.
As there seems to be many versions of matching components depending on which source of information is used...
Hello,
I am currently developing a firmware where I am acting as a server with nRF52840.
The protocol of my use case is:
Client is connecting to my device (server...
NRF52: SDK v2.1.1
NRF91/SLM: SDK v2.0.0
We are seeing an issue with NRF52840 / NRF91 interaction over LPUART. When NRF91 powers up, the bootloader is not using using LPUART...
hi dev
I have a question about nrf52 dk board.
I have 2 dk board : one was written 2021.06 and the other one was written 2022.12
anyway, when I debug same file which...
We have a custom nRF9160 board which in Zephyr v1.7.1 defined in the boards\arm tree. It is a near copy of the nrf9160dk_nrf9160 folder with hardware changes and additions...
Hi Everyone,
I am using NRF52840 in my project and compiling my code using sdk 17.0.2. My application requires 7 interrupt pins to be enabled. However when I am enabling...
I have nrf9160 custom board, and I have issue with SIM module. I'm not getting 1.8 volt in "SIM_1V8" pin.
- I download the latest version from nRF Connect SDK v2.2.0 from...
