Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello,
I'm trying to compile the examples\dfu\secure_bootloader\pca10040e_s112_ble_debug\ses project, I have modified the flash placement according to the memory layout...
Hi,
I am trying to program nRF52840 dongle (PCA10059) with PlatformIO and Arduino framework, but the program (see below) won’t start. I think it falls in the hard fault...
Setup:
nrf connect sdk version v2.1.2
board: nrf52840DK
Trying to send a beacons for half a second whenever I get some specific data on uart, and also send data over...
Hi,
We have multiple controllers connected serially(using SPI/UART) to the NRF5340 controller in our product. We have a requirement to download multiple images(4-5) for...
We are working with adafruit Nrf52832 and have a weird problem, the Ground pin and 3.3v pin is shorted and it also shows a 3.3v between them. Can you please help regarding...
Hi there,
I wanted to bring up the Bluetooth samples on NRF5340 development kit on NRF CONNECT SDK v2.2.0.
After building and flashing it, I can see the UART log on my...
Under:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_thread_tools.html#configuring-a-radio-co-processor
steps listed for 1 and "nRF52840 Dongle (USB...
Hello,
I am starting working on a nRF9160DK board, but I am new to this and I am a bit lost.
Using the Dev Academy course and example, I was able to make a small project...
Looking at the docs: nrf/ug_thread_architectures.html
I see the note "This platform design is currently discontinued by nRF Connect SDK." for "Network co-processor (NCP...
Hi All,
We have 2nos. of NRF5340 DK board, in which we are trying to run the "broadcast_audio_source" from nrfConnect SDK 2.2.0 sample installed from nrf Connect desktop...
hi team,
i have trying to wrote a code for saadc module in segger 5.40 using nrf52840 controller. whenever i am trying to increase the Acquisition time the sampling value...
Hi, I want DFU the NRF52840 using the UART. Please let me know the following quires .
Process-
I want to create two partition of memory one will store the my main application...
While running the mentioned code I am getting stack overflow error continuously. Can someone help me understand the reason behind that and what can be done to resolve such...
Hi, I am trying to do the SPI communication between a SPI master and two SPI slaves. I am using NRF52840 Dev Kit as SPI master and 2 ESP32-S3 as SPI slaves. I am using SDK...
