We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I am developing a product using the nRF52840. I am currently running into a difficult problem. I inquired about it 2 years ago, but it has not been resolved.
I need to process...
Hi, on the nRF52820-QDAA I am using pin 5 AIN3 / P0.05 as an GPIO output to drive a LED (active low).
This does not work in the software, when I drive the pin high with...
Hello,
NRF5340, NCS2.0.2, VScode
I designed a headset，MCU is 5340, and a external flash for DSP program.
the external flash connect to DSP and 5340 use SPI;
i can...
Hello,
I was able to build the nRF Desktop sample application on the nRF5340 platform, but when trying to debug, I get the following error:
Here is my build configuration...
Dear ,
I am going to use debug out function on RF5340 DK.
connection is as below: customer board conncet to nRF5340DK.
customer board use nRF52833.
I tried many times...
Hi,
I was just wondering if the nrf52840 Dongle is in some ways inferior to the other development boards in terms of its capabilities?
As I was going through the examples...
Hi,
I am using a nrf528409dk for my application development using nCS. I have various features from which I need to understand how to add some high priority features into...
Hi,
I'm working with the ncs 1.6.1 peripheral_uart example and am looking to increase the size of the data frame to send 240 bytes per data frame.
I have seen several...
I am taking mqqt_simple of NRF9160 as reference for this question,
This is questing regarding, what is recommendation / Philosophy of using MQTT in NRF9160 with other codes...
Hi,
I'm programming a custom board based on Taiyo-Yuden EYSHSNZWZ module (with nRF52832).
I'm using the secure_bootloader example from SDK for OTA DFU, in order to flash...
I'm using the nRF-PPK2 to measure device power usage. I've noticed even at low sampling frequencies (>= 100Hz) it exhibits considerable lag at some point. Most annoyingly...
Hi Sir,
As we know the nRF5340 doesn't release the Circuit Board Guidelines (nAN-40) like nRF52840 yet.
If we need to design the nRF5340, could you share the recommended...
Hello,
I'm doing a comparison between MQTT on TCP and CoAP on UDP over NB-IoT and LTE-M. The communication to the cloud works as expected for both protocols. MQTT is used...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
