But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi Team,
I am using nRF5340 dev kit and NCS(Nordic connect SDK 2.0.2)for my DFU POC purpose. I want to perform DFU update of nRF5340 through nRF USB port instead of the...
Hi developers,
Now, I want to get a correct Tx power value. I printed out the value from "ble_gap_evt_t->params.adv_report.tx_power" and could get only 127, even this...
Hi,
I am using 5340 but it's uart consumes a lot of power 2.01mA
SDK: NCS2.1.0
project: peripheral_uart
I have disabled all other peripheral equipment,put all...
when I open nrf connect for desktop i got blank page,
and there nothing in the console:
I've installed/am using:
nRF Connect for Desktop v.3.11.1
J-Link V7.68b...
Hello,
we are using the nrf9160 in one of our products. Our assembler has used old nrf9160 SICA B0 chips on our first protoyping round. When we run our software on the nrf9160...
Hello, Guys.
I had problem that if I config nRF9160 through UART0 (default) it works and I receive IP address and can make MQTT connections.
But when I use UART2 (external...
Background:
I seek to interact (human and/or additional MCU) with both UART peripherals (uart0 & uart1) in the easiest manner possible - issue commands, pass traffic, etc...
I have shell working with the following configuration
CONFIG_SHELL =y
CONFIG_SHELL_BACKENDS =y
CONFIG_SHELL_BACKEND_SERIAL =y #also selects serial
CONFIG_SHELL_CMDS...
Check the below C++ code:
in file S.h, we define class S
in file S.cpp, we implement S constructor and function init()
in file test.cpp we first declare a global...
Hello there,
I am looking for a way to connect to the Eclipse Leshan Server without DTLS using the LwM2M Client sample. However, this does not seem to be so easy.
The...
I try to run nrf sniffer with Wireshark.
I flashed sniffer_nrf52840dongle_nrf52840_4.1.0.hex
I download and run nrf_sniffer_ble.py.
I got this error and I cannot find...
Hi all,
For a project I need to use a private library which uses the app_scheduler to queue events triggered from a second MCU. I am using FreeRTOS on the nRF and I am unsure...
Dear Support,
as suggested I create specific question based on this thread:
Could you please confirm that the QSPI peripheral makes polling of QSPI flash Status Register...
I was trying to implement the nRF5_SDK_17.1.0_ddde560 proximity example into the template.
After getting all the functions working and the application compiling, the board...
For some reason the microprocessor will not wake when P0.07 is pulled low. I have an external 10kOhm pullup so there is no need to configure the internal pullup. If I change...
