But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hi,
Just wonder does NVS only use half of the configured size? I have configured the nvs_storage size = 0x2000 ( 8192 bytes)
So sector_count = 2 (4096 / sector)
When...
Hi Team,
We are in process of developing pairing mechanism for our peripheral device. We are considering using NFC for OOB. Here is what we think we should be doing: ...
Hello People,
I am working on a custom board and while trying ble_app_uart example code instead of the advertising name given in the code the device was showing "DFU_TARG...
Per the documentation on multi image builds , a child image folder that contains a <board>_<revision>.overlay it will be merged with BOARD.dts but I cannot do the same for...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
I used to use the ncs1.2.0 SDK to develop a product for customers. Now I am porting it to the ncs1.9.0 SDK. During the adaptation process, I find that its control over SPI...
Hello,
I have a few queries:
I need to confirm that does Thingy53 board support TensorFlow lite. So, for my ongoing project, I am using TensorFlow to develop my code...
Hello,
I am facing an issue at running otbr docker conainer on my RPi4 with nRF52840 Dongle as an RCP device . I am getting this error on the logs: Aug 24 16:05:07 0e6bb978e199...
Hi!
I have tried to get the secure_bootloader working on the nRF52820, but I think the linker settings are not correct yet. Maybe someone here has already written a bootloader...
Hello,
I am trying to build OpenThread Radio Co-Processor (RCP) firmware for nRF52840 Dongle with the new nRF Connect SDK v2.0.2. My VM is running Ubuntu 20.04.3 LTS with...
Hello!
I have an application that makes use of the function sd_ble_gap_conn_evt_trigger_start() , present in v7.3.0 of the S113 , S132 , and S140 SoftDevices. Here's the...
Hi,
1. I can use Programmer in nRF Connect for Desktop to flash the hex file ( nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images\ble\nrf52832sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
