Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello everyone,
is there an example that demonstrates how to turn off and on the Bluetooth completely multiple times in the application?
I need really low consumption...
Hi All,
I am new and trying to connect External BLE Pressure Sensor to NRF52840-DK Board
Do you have any example code for interfacing external BLE sensors that I can refer...
Hi, I am trying to connect the AWS_IOT library to a thread netork but find it really hard to get the TLS sockets working. I have connectivity for normal TCP and MQTT as well...
Hello,
our project has a requirement,
nrf52832 is used as a peripheral, and the mobile phone is connected to nrf52832.
The amount of data is relatively large. We want...
I want to use nvs in nrf cloud. A conflict is found between the nrf_cloud library and the nvs library. The nrf_cloud library will cause the nvs library to be unavailable,...
Hi, I have a product working with an android app with the nordic library for a nrf51822. I'm using auto connect but I would like just before performing a DFU to change this...
Hello,
I'm trying to run the MQTT simple sample, i don't know why but i can't build and run the project and also i cannot connect J-link.
Do you have any idea?
Thank...
Hi
If I log to RTT I can see ZCL packets decoded on the log using minimal logging but when i tried it with full logging (to get that on the zigbee_shell on the uart) I got...
Hello,
We have a custom design board using Raytac MDBT50Q-1MV2. We'd like to use the DC/DC regulator for REG0 stage for low power consumption. Please see the relevant part...
Hello,
In our product, we use the S132 v3 softdevice and legacy pairing with a static pin code. At startup, this pin code (that can be changed by the user) is read from...
in sample peripheral_uart in NCS1.5.0 ,I want to re-binding uart0 rx and tx pin . the default pin is p0.20 and p0.22 ,i want to rebind witn p1.0 and p1.1 .but i edit in prj...
Hello, I bought the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - V3.0 from Adafruit Bluefruit.
So, I downloaded nRF Sniffer for Bluetooth LE 3.0 and...
Hi,
I am trying to apply a whitelist during advertisement on my peripheral device. Only one central should be whitelisted at a time. The whitelist is empty on initial...
Hi,
I'm using nRF52840 with ble_app_uart of ble peripheral example. And I'm using IDE is SES.
I want to put two deep learning model into my project , the two deep learning...
