I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
When developing the dfu upgrade device, the code can be loaded to 100%, but the prompt "remote dfu invalid crc error" The compiled firmware can be upgraded with the old nRFtoolbox...
Hello,
I'm trying to get the PCA10056 to communicate with the MPU6050 Motion Processor (I think that's what it's called), but still in the very starting point.
1 - I've...
I've been using STM32 controllers with LoRaWan mostly GNU based and bare metal. Recently, I have been looking at the STM Nucleo STMWB32 communicating with a Raspberry Pi and...
Hardware:
PCA10040
V 0.9.0
2015.47
Hello,
I connected the above development kit to my PC today and was prompted to update the J-Link firmware ("Strongly encouraged...
Hi,
I am using SDK16.0(ble_app_uart) program to sending dates between the phone and board.When I use my iphone xs max,it works on well.But it come out some faults when it...
I have a compile error currently: "section .heap overlaps absolute placed section .stack"
The heap size is currently set to zero.
I am guessing I am just going over the...
I keep getting this error code and while debugging I'm able to resume execution. This error seems to be thrown during my DMA transfers over SPI. Is there somewhere I can look...
I have a Thingy 91 and trying to connect it to nRF Cloud without any success so far. It is not connecting to GSM Network.
I updated both modem software and application...
At least using the LLD linker, it is possible to locate RAM segments of known size (.bss, .data, heap) at the end of RAM. Normally this allows placing the stack under these...
Segger Embedded Studios 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 custom board
Hi,
I use this code to start network formation on Zigbee:
zb_bool_t comm_status...
I've had nothing but trouble attempting to get the SUPL library work. I finally was able to get it working on the 9160DK with the latest modem software and GPS sample. However...
Dear All,
I am experimenting with the nRF52840 DK and the ble_app_template . Based on that project, I am trying to configure a pin interrupt on Button 1 (pin 0.11). This...
Hi,
The project I am working on involves streaming 8 audio streams (16 channels of data), and I was hoping to use the nRF52 for this purpose. Does anyone have any ideas...
When we test the BLE conducted power, we find some phenomena, when IC power is setted to 0dBm, the active power loss is similar with passive path loss, it is consistent with...
Hi,
I would like to save my project and add something like a version number to it. I use an example from nordic SDK. So in my case I use solution from ...\examples\ble_peripheral...
