But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello everyone,
I'm trying to set up entirely open source project for my NRF51822 chip. Everything works fine so far but something strange happens during debugging.
I...
Hello support team,
I am using your product through a module vendor and I have a question regarding errata 197. If the DC/DC regulator only has problems in low power states...
hi... i am using nrf52840 and nrf52832..... mesh sdk 3.1 latest version ....
in this case i am using client as nrf540 and server as nr52832 .... i have debugged the light...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
I am working on an nRF52832 BLE peripheral prototype which sends bulk data to a central as bursts of large notifications. I am encountering an error where the connection gets...
We are manufacturing 2 types of gas sensors that communicate BT LE. One use an nRF52832 and the other an nRF51822. Will the nRF52 dongle communicate with both of these? Is...
Hello
I am currently programming with keiluVersion4.
Previously, I used "fatfs example" of SDK_15.0.0.
So trying to test the function of BLE, trying BLE communication...
Hi ,
I'm working on a 2.4GHz wireless microphone project now.
I want to make a scheme of two microphones transmitting to a single receiver(2T1R)。And ,i have tested this...
Hi, Andreas.
Following the guide you find in the document " Buttonless Secure DFU Service ", I get errors while trying to compile. In order to ascertain were is the problem...
How to realize the USB HID interface and PC data transmission?
I want to connect my computer via USB hid protocol for communication
This is my code, but can only send...
Hi everyone,
I am a beginner for BLE software development with MDK-LiteV 5.26.2.0.
Target device: nRF52832（EKSHCNZWZ made by Taiyo Yuden）
SDK: nrf5_SDK_15.2.0_9412b96...
