Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi, I tried the above tools(nrfjprog) on the Raspberry Pi 3.
But, I saw the error shown below.
pi@raspberrypi:~$ ls | grep nRF5x
nRF5x-Command-Line-Tools_8_5_0_Linux...
We are trying to modify the nRF Beacon example app for iOS that Nordic provides. We are unable to get app to see the devices from the iBeacon kit when they can be seen from...
The manuals for the nRF51 and nRF52 list the maximum ESB radio channel number
as 100, but in the SDK the guard value in the set channel function is <= 125
(in both the...
I am about to start development on a project that will be using a pair of nRF52832's to make a low data rate connection between a PC (with a nRF52832 based dongle) and a device...
In the event that a Nordic soft device library call fails (as determined by APP_ERROR_CHECK() macro) and our application level app_error_fault_handler () function is called...
Hello,
Ported my FreeRTOS application on NRF52 from SDK 12.2.0 to SDK 13.0.0 .My application is using freertos apptimer for timestamping and waking up of device which was...
Hi,
I am trying to run a ble mesh example but I prefer to work using keil, because I already worked other examples using the SDK (12, 13 and 14) and PCA10040/PCA10056 nordic...
For a precision timer application I have an external temperature compensated RTC (DS3231) which produces a highly stable 32 kHz signal connected to pin 5
When I associate...
Hello,
I am rather new to BLE and the NRF5x.
I want to build the following application: a swim timing sytem. The system consists of master timer with a high precision...
Hey,
I have a few questions about dynamic multiprotocol BLE/Thread support.
1. Multiple BLE connections. If I have one connection and connection event length is set for...
I'm working on a bootloader using the /examples/iot/bootloader as an initial template. The image to flash is stored on SD card. I'm at the point where I am successful in writing...
Hello.
i setup - BLE Stack + Uart 1 + SPI 1.
Infinite loop inside nothing code.
nRF52832 consumed 5mA + a.
and i add power_manage() in Infinite loop.
Nevertheless...
Hi,
We are potentially considering using nRF52 DK in our projects. Kindly advise on following questions,
(Q) How we can use uC/OS-II or uC/OS-III with nRF52 or other nordicsemi...
Hi,
I am testing the experimental_bootloader_secure_usb example.
I have confirmed that the old v0.9.2 board has been replaced with a new board and connected to the ...
