But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I want to compile the ble_uart example using Segger Embedded Studio. I installed today the latest version V8.16. I am using nRF5_SDK_12.3.0_d7731ad.
I imported the project...
Hello,
I'm trying to change the name of the USB port in the "usbd_ble_uart_freertos" example code. Currently, it shows up in the Device Manager as "USB Serial Device (COM12...
I am developing a simple BLE mouse using ble_app_hids_mouse of SDK17.1.0. I found out through devzone that left mouse button click sends (1, 0, 0) and right button click sends...
I'm unable to load values into characteristics—they show up as N/A on the nRF Connect app. I tried to enable notifications using the Client Characteristic Configuration, but...
Hi Nordic Community I have a problem with the PAwR examples were I'm unable to place a sync interval bigger than 2 secs.
The example starts with an interval of 0xFF * 1...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi team,
We need to interface STM32L4(Host MCU) with WT02V40V in our design.
Is UART communication enough for interface both?
And also, Is CS pin common for SPI and...
Hi Support Team
We want to use nRF7002 and nRF54L15 to implement Wi-Fi, could you provide us the hardware reference design of nRF7002 work with nRF54L15 ? Many thanks.
Hello Everyone,
I am designing the BLE peripheral which is connectable, we have our own BLE mobile application. I am trying to configure the peripheral to be visible to...
I am attempting to compile the nrf sample code for peripheral uart and I encounter a fatal error in the extensions.cmake file. Apparently the CACHE_VAR_REQUIRED is set somewhere...
Hi,
I uninstalled my VScode earlier for some other reason, and when I reinstalled it and upgraded toolchains and SDK to v2.7.0, I found that my VScode couldn't find my board...
We are developing the project ARGO .
At the current stage ARGo is going to Support NB-IOT communication
A mother board is under development to support the mini-PCI card...
Dear Sir/Madam
I have installed the Jlink driver and nRF sdk for 9160 on my macbook.
I use the nRF Connect for VS code to program, but I can't see the device under the...
Hello,
I'm trying to get some basic SPI communication between the nRF91 and nRF52 chips on the nRF9160DK. We have been using UART for this communication however we want...
"The nRF52840 is developed using NCS v2.6.1. When the ADC is set with the reference voltage as (.reference = ADC_REF_VDD_1_4, .resolution = 10), the ADC sampling output is...
