This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I attached an external nRF52840 to the debug out port of the nRF 7002 DK (as seen here ), but cannot get a connection to the external uC.
I know the cable and uC work...
Hello Nordic community,
I’m working on a project that primarily uses GPIO for controlling locks, Bluetooth communication, and is powered by a battery. I’ve attached the...
Hello，
I am using a customized NRF52832 circuit board. During the Bluetooth connection test with a mobile phone, the connection suddenly disconnected, and then quickly reconnected...
We have an nRF9160 based product with firmware based on your AWS IoT Core example. Our devices are connected to the Telstra CAT-M1 Network in Australia (50501) using Modem...
Hello,
currently tampering around with "how to find out state of BLE TX FIFO", see e.g.
Next idea: is there any way to access BLE transmission/reception statistics? So...
Hi,
I am hit with a noticeable ram usage bump (~10%) when migrating from 2.5.0 to 2.7.0. Upon generating the ram_report, I notice that net_buf_data_hci_rx_pool has a huge...
The database that nRF Connect for Mobile pulls definitions from is significantly out of date (exact age depends on the category)
https://github.com/NordicSemiconductor/bluetooth...
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
My issue is that even when using...
Hi All,
I am building a event driven IoT application thus using the Nordic CAF I like to know if the Nordic and/or zephyr (system) threads are running fine (if not the watchdog...
Hello,
I am currently migrating from NCS 2.6.0 to NCS 2.7.0 on my board with an NRF9160.
During that process I switched to the new hardware model and to sysbuild. As far...
Hi,
I am getting the following error: CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/extensions.cmake:2891 (message):BOARD is not being defined on the CMake command-line...
Dear Team,
This is my first embedded project.I am basically from Analog design background.
I connected the nRF52840-DK board as shown below.
I connected the board...
Hello and thanks for reading. Our device needs to act as both a central and peripheral. I have written all the peripheral code, and its all working perfectly. However, once...
Hi,
I have a project in which I'm using the nRF52840 with OpenThread and the device is configured as an MTD to minimize power usage. I have recently updated my nRF Connect...
