This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
Currently, I know that OTA updates for the nRF5340 can be performed using Device Manager and the nRF Connect mobile application. However, if using a PC, is it possible...
SoC: nRF52832 or nRF54L15 SDK: nRF Connect SDK v3.2.0
We are considering controlling coexistence via PTA signals when operating a third-party Wi-Fi device together with...
On this page https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/build/dts/howtos.html#set_devicetree_overlays and many others in this documentation, it appears that...
The subject issue is documented here as " NCSDK-20567: Partitioning limitation with MCUboot swap move": This issue has been open for while. These two DevZone tickets refer...
I use ncs3.0.2 to develop the 54l10 chip. I created a timer using k_timer, with a period of 1 second, to record the device time. Although I have adjusted the load capacitors...
I'm attempting to enable provisioning using attestation tokens in my project. As soon as I add the config;
CONFIG_NRF_PROVISIONING =y
The build starts failing with;...
Hi,
We are facing a strange behavior where the consumption we measure on the nRF5340 doesn't change according to supply voltage like it is supposed to do in DCDC mode. ...
Hello Nordic team,
I want to be able to save the log into a file and then read it in order to send it's content via HID.
I've managed to make the log back end FS work...
I have a nRF9151 based device, modem firmware version v2.0.3, with `CONFIG_LTE_LC_RAI_MODULE=y`, registered on LTE-M.
Using `NRF_RAI_LAST` is working, but I am seeing odd...
For the nRF9151-LACA-R, I cannot find the flatness parameter in its datasheet. Can you help confirm the flatness?
For the nRF54L15-CAAA, the datasheet shows A3 (0.03...
The MCP server requires authentication. To complete the setup, you'll need to: 1. Get an API key from Nordic Semiconductor / Kapa.ai 2. Reconfigure the server with the auth...
Hi All,
My leds on the custom board wont get recognized. Keep getting this error.
A bit of strack trace:
Device tree:
I think I am missing something...
Hi,
We're coming to the end of prototyping a project on the Thingy91X and are fine-tuning the power management. We have been able to implement a simple demo on the nrf9151dk...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
