But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Dear All,
I am trying to use sscanf in a project and I am getting the message that it is undefined. I am including <stdio.h>.
I cannot understand/find the reason of...
Hello everyone,
I'm taking the "Bluetooth Low Energy Fundamentals" course For all the examples I followed in the training, from what I understood, we loaded the peripheral...
Hello, we are trying to use the shell over bluetooth but in default it also uses the uart contorroler of the board. us there any configuration option to disable the zephyr...
I have not messed around with devicetree much before this point. I'm trying to create a custom dts and bindings for my device. Within my custom dts file, I reference the nRF52833...
I am working with nRF52840 with MAX86141 and learning how to setup the SPI connection
Here is an opensource example : https://github.com/JON95Git/zephyr-spi-directly
And...
Hi Support Team,
I am using the nRF7002DK board for our product POC (Proof of Concept) purposes. We plan to use the same MCU, the nRF5340, for our final product.
I have...
Hello,
I am using an nRF9160dk with the nRF52840 acting as the BT controller running the Bluetooth: HCI low power UART sample ( https://developer.nordicsemi.com/nRF_Connect_SDK...
modem_info_get_current_band expects an uint8 pointer to store the band into, but scans for an unsigned int (probably above 8 bit) in nrf_modem_at_scanf. This leads to memory...
Hello
I am working on a WiFi application using a custom board equipped with both the nRF5340 aswell as the nRF7002. When requesting a WiFi connection using the net_mgmt...
I'm using 2 nRF52840 DK to run a data transfer test between a central and a peripheral.
The Central device uses ble_app_uart_c, The peripheral uses ble_app_uart. These examples...
We are trying to re-layout the PCA10059 Dongle. I would like to continue to use the existing USB bootloader .hex file for updates via CDC_ACM. One thing I am confused about...
Hello, DECT NR+ seems as a good fit for our product, however, current stack providers(Wirepass and Lynq) are not suitable for us. I'm wondering are there other companies who...
Since the tickets are scattered, I will summarize the questions about nRF5340 Audio again.
Prerequisites
NCS version is 2.5.0. Raytac's MDBT53-1M is implemented on a homemade...
Hi Team,
We are using SLM SDK 2.4.0 and MFW 1.3.5
We moving forward to SLM SDK 2.5.2 and want to FOTA all our products outside, but, some have problems with cellular...
