Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
I'm developing with NCS v2.6.0 for Raytac MDBT53v-P1M module, which inhibits nRF5340. I already have my own PCB with all the required HW components.
As a sanity check...
Hi I would like to report a bug in the Devicetree visual editor.
When you add two fixed regulators and connect a separate sensor to each of them, both sensors will be represented...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi,
I have a new NRF5340-DK and I am trying to connect it via usb on linux but do not see it in the syslog when connected. I actually do not see anything at all.
When...
Hi,
I want to implement a pwm output signal on a particular pin of the nRF52840DK working with the latest nRF Connect for VS Code. What would be the recommended way to setup...
Hi,
I tried to flash the blinky example to an nRF52840 Dongle as described here:
https://academy.nordicsemi.com/flash-instructions-for-nrf52840-dongle/
Console output...
Hi I'm trying to create a transparent CDC to NUS bridge, this is based on the nrf52840 dongle.
The Aim of this is to send binary files to our device from a PC, our device...
I wrote a code for GPIO interrupt when DRDY pin goes high to low(Data ready) interrupt should occur and call a function but it is not working Below is a code:
intDRDY =...
Trying to implement FOTA DFU over BLE. My application uses my proprietary code (instead of mcumgr) to download signed OTA firmware image to secondary slot (in my case it is...
I am working on an application with significant constraints on power consumption and distance immunity. After some research, I found the Thingy:53 module, which is well-suited...
We had tried AT#XSLEEP=1 command in nRF SDK 2.5.0 and it worked. We saw it working for both modem FW 2.0.0 and 2.0.1.
When we updated SDK to 2.6.1 and modem FW 2.0.1, the...
I am building and running the Serial LTE application on a nrf9160. But am facing an issue with the application going into a reboot loop when network is activated.
I am using...
