But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I'm developing a Matter device based on the Window Covering sample. I have added another endpoint to the device containing some sensor clusters and it all works after...
Hi,
I am looking for a constant-time memory comparison is a function that compares memory for equality in a fixed amount of time, regardless of the data's content. I am...
We're currently developing a zephyr firmware on zephyr 4.2 and we got a custom board for our hardware powered by an nrf52840-ckaa-R
the first time I connected the board...
Hi all.
I've attached a single channel microphone onto my nRF9151 and I'd like to capture blocks of audio for processing. I've configured the device tree like this:
i2s...
Good evening.
I am working on a USB HID joystick. The USB documentation on nordic, while better than the woefully inadequate zephyr mainline docs, only covers the surface...
Hi,
I'm designing my device based on the Thingy53 layout and I have some questions:
The first is why, in the T53, the antenna division comes through U17 (PE4259) instead...
I recently began testing with the nPM1300EK and it seems like something is wrong with it. A number of different tasks don't seem to be working correctly:
Profiling a battery...
Greetings,
Using SDK v3.1.1 the SPI MISO signal appears to be actively driven by the nRF5280 for both my SPI1 and SPI2 configurations. In both cases there are no active...
Hi All,
I have to validate following use cases:
N reflector with nrf52833
1 initiator with nrf5340
The nrf5340 will be able to :
calculate distance from each...
Hi,
we are implementing MCUmgr SMP OTA over BLE (Zephyr + nRF54L15) with flutter, and I want to confirm that I’m generating the correct SMP upload packet format before streaming...
Hai, i try to MFRC522 rfid reader interface the nrf52833. 1. I try the read version from reader but it's only show the 0xFF 2.I try to read the card id . it is not work. I...
I'm unable to import/export mesh networks and then subsequently send mesh messages. I believe this problem has been mentioned before [ 1 ][2][3], but the solutions offered...
Hi,
We've had a mesh sensor network all working for a long time using SDK17.0.2 + Mesh SDK 4.1.0
The data is accessed by a mobile app through a mesh node acting as a proxy...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
Hi Nordic Team,
I’m currently using two standard nRF5340 DKs (non-Audio DK) running the nrf5340_audio application.
We’ve successfully adapted I²S speaker output on unicast...
