Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Dear,
- nRF connect SDK 1.9.1
- nRF5340 DK
We use 5340 spi to control an adc chip. The sample rate we need is 1kHz, so we use k_timer to produce a 1ms timer.
However...
The issue is as stated in the title. The 'Select Device' column says "Connect a Nordic development kit to your computer" when the Power Profiler is NOT plugged in. This imediately...
Can someone help me with a Zephyr compiled blinky hex file please?
My Hardware is a loose standing module setup similar to NRF52833 DK. (same led_0)
NRF5 Sdk hex file...
I am using fstorage to store some data at three location in flash.
but it is hanging at wait_for_flash_ready function when mobile phone is connected through BLE.
Please...
Hi everyone, I am quite newbee to nRF5340 and nRF ecosystem. Anyway, my goal is to talk with 3rd party application to receive positioning data over bluetooth and then I have...
Working with nRF52840 and nRF Connect SDK v2.1.0., whenever I enable MCUboot in the project configuration, the reset pin gets enabled on the next flash. I believe this has...
Hi,
I encounter a problem, in my opinion, related to the modem firmware (or model B0 and B1).
My program connects to the LTE-M network and sends data from a sensor.
...
Hi all.
I'm working on a Visual Studio project, written in C++, which I'd like to import into Segger Embeeded Studio.
I've done this before successfully, but this time...
hi support team,
customer reported one problem that when 5340 spi communication is done, the clock line is much longer than cs pin as below:
number2 is clock pin, and...
Hi,
In the example "nrf52832 light_switch_server" ,Does it have the function interface for the friendship node adervertise to all lpn nodes at one time?
hope your reply...
Hi there,
there is so many questions regarding BLE connection intervals, yet I couldn't find a precise answer to this basic question.
It seems to me, that multiple packets...
Dears,
I am working with nrf52 SOCs using nrf connect sdk.
I want to try the SMP Server Sample for OTA firmware update.
There is a tool called mcumgr-cli that cannot...
How are private keys stored on the nrf9160 modem? I've read in other forum posts and observed that the private key cannot be read out once set in the modem. Where could I...
According to this discussion, all the 4 UARTs are functional in nRF5340. I intend to use multiple UART ports, and I modified this exercise solution to do so. I was able to...
