But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
nRF9151, mfw 2.0.2, NCS 3.1.0
I currently faced issue in calling "lte_lc_power_off" (resulting finally in an blocking call of "nrf_modem_at_printf("AT+CFUN=%d", mode)" ...
We moved a Zephyr project to SDK 3.0.2. After that it is possible to compile it on Mac and Linux machines but on WSL I'm getting an error:
Looks like I miss some environment...
I tried to use west rtt with v3.1.0 and I'm getting the following error:
ERROR: runners.jlink: [Errno 22] Invalid argument
How to reproduce:
Connect J-Link to Thingy...
I have a battery application where I power off areas of the circuit. One of which has my I2C/TWIM peripherals. However, the TWIM controller configured on the nRF52832 is pulling...
Hello,
we are trying to test the fast pair example: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/fast_pair/locator_tag/README.html
However...
Estou desenvolvendo um novo perfil de bateria. Após completar o ciclo de aproximadamente 48 horas em temperatura ambiente, aparece a mensagem "Algo deu errado durante o processamento...
We are shipping a product with a custom board based upon the nRF52833 SoC. We can update our firmware in the field.
We are trying to minimize the power draw of our product...
I have been working with MBN52832DK in Vscode . The sample examples i have tested is "Hello world", "bluetooth/peripheral_uart" ," peripheral lbs".I have been able to connect...
Hello Nordic Support,
I’m encountering a critical issue with the nRF54L15 device, custom board.The custom borad is flashed from nrf54l15dk ,PCA10156. After flashing firmware...
Hello, is it possible to somehow use RTC0 peripheral onboard an nRF9151DK to store real time so it will be available (sustained) even after resetting the device? As far as...
Hi, I used nrfjprog -e to the nRF54L15DK and problem is in Programmer log.txt How to recover nRF54L15DK does we need to update the nRF5340 JLink debugger?
I configured VBUS with a 1500mA limit. In theory, VSYS should deliver something similar to this. The VSYS output is 5V; it powers some LDOs in my project, which consequently...
Hi, I’m trying to generate a PWM signal directly using the nRF5340’s PWM peripheral registers (not using Zephyr’s pwm_dt_spec or driver API).
The LED turns ON correctly...
Hello,
I am trying to adapt the "Interfacing with a sensor over SPI" example from the nRF Connect SDK Intermediate Dev Academy course in Lesson 5. When I run the code as...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
