Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
Hello everybody.
I am developing a BLE application in which I am using WDT every 12 seconds and a RTC interrupt every 10 seconds to send some information.
When you press...
Hi,
We are using nRF5340 and we are migrating to v2.0.2 NCS sdk from v1.9.1.
In our design, the SPI MISO pin is P0.10. From the dev zone tickets, I found that this P0...
Hi,
I'm trying to send I2S data (~ 16 kHz, 24 bits) via BLE using the nRF52 DK and the nRF5 SDK 17.1.0. After I get the data from the I2S driver (by specification, they...
Hi!
To measure the voltage level of a coin cell CR2450 can be done in different ways.
You can use the comparator, the low power comparator or the ADC.
I wonder which...
Hi, The getaddrinfo() function returns the same IP address for www2.domain.com and domain.com, namely that of domain.com while they are running on different servers and have...
Hi
I am currently working on a Matter project.
I configured OTBR with Raspberry Pi, completed pairing with nRF52840 board (Light bulb), and confirmed that Light on/off...
Hi,
In order to make firmware updates over Bluetooth work, I need to enable the MCU boot loader. Is use CONFIG_BOOTLOADER_MCUBOOT=y in my prj.conf file to enable it. My...
I'm doing with the nRF Connect SDK v.19.1, testing the project C:\ncs\v1.9.1\zephyr\samples\hello_world.
The main. c file is
void main(void) { printk("Hello World! %s...
Hi， i'm use latest ncs develop bluetooth extend advertising, and i'm try use west build -t menuconfig to config scan filter config
such as BT_CTLR_DUP_FILTER_LEN or BT_CTLR_DUP_FILTER_ADV_SET_MAX...
I want to define config values in an optional overlay that is enabled after writing to a custom service/characteristic using NCS. Based on this https://devzone.nordicsemi...
Hi,
in my company, we are using an nRF9160 on a custom board. Recently we updated from NCS 1.8.0 to 2.0.2 (we also still use spm for now).
1.8.0 was already not super...
Hello all, Ive combed through the NRF52840 datasheet and the BMD341 datasheet, and SDK examples attempting to determine if through software (and possible hardware change)...
Hello,
in our application we want to use a simple serial Spi Flash: M25P40 (only 1 data signal).
For evaluationI I connected this Spi Flash to the nrf5340-DK Board:
...
