But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Good Morning people. I'm developing a module with the soic nrf52832 and I'm having doubts about the electrical schematic of the UART communication with another MCU. I analyzed...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
Trying out Nrf5 sdk v17.1 with SES 6.32 and opened up an ANT+ example `ant\ant_debug\d52\s212\ses`
Tried to build, 50% compiled successfully, but i get repeated errors on...
We use nrf52833, and the SDK is 17.1.0. We have the following questions about gzll: 1. How to count packets_num and timeouts_num in Packets Statistics? timeouts_num Where...
Hello,
I am trying to send a large file through BLE from an nRF52811 to a Raspberry Pi 4. File size is about 77 kilobytes.
Here is BLE setup on the nRF side:
Custom...
Using the DM, in the discovery_complete callback, after finding two CCC handles from 2 custom UUID's, I can subscribe to only one of the two, the other fails with EALREADY...
Hi,
I am not sure where to go next, so looking for some debug help.
Setup : I am using the 9160DK - the 52840 is being used as an ANT+ receiver, where it forwards on UARTE...
