This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm currently working with an nRF5340DK , trying to implement FOTA update by sending the firmware from another nRF5340DK . Is there an already developed feature/sample...
Hi,
I'm using the nRF5340 DK. I am trying to get iso_broadcast sample application working but it fails when creating a BIG (-5 error) (there is a prior support ticket for...
Our startup previously used nrfx 2.4.0 but worked just fine. Upgrading to nrfx 2.8.0 results in a Hard Fault at the location seen in the screenshot. Which is the file located...
Hi,
I am posting this here because I am not sure exactly which repository to file the bug on (zephyr? west? something else?)
nrfjprog supports programming over IP with...
I'm still new to Zephyr, so this could be an easy question that I'm googling poorly - if so, sorry in advance. I just wanted to add an extra LED, led4 , to the existing nrf9160dk...
Hi everyone, and thanks for all the help provided on this site !
I have tried to flash a MDBT42Q using the nrf82832-DK (PCA10040) and it works fine for simple peripheral...
Hello,
Aim : Our application uses the PC-BLE driver for serialization purpose as well as the nrfutil for DFU purpose in the same script, we switch between the two by opening...
Hi,
I am developing a BLE sensor based on nRF52840 SoC (QIAA aQFN 73). I would like to get some clarrification regarding following points while hardware design. Thanks for...
Hi there,
We intend on using the default Serial LTE Modem example on the nrf9160 in our product. We will then communicate to the modem with AT commands from an external...
I'm trying to program a nrf52832 chip with a nrf52dk board by configuration below, referred to https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using...
Hello,
Since the last update some of the includes in my files are being marked by VSCode as "cannot open source file xxx (1696)"
The application compiles fine...
Hi! The nRF9160 has a nice, accurate LFXO integrated. I'm assuming that it's also active most of the time anyway to provide timing for the modem (assuming one is using the...
Hi, I have the following questions. Please help me answer them: Using the protocol stack of the above version, one master and two slaves are disconnected when reconnecting...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
I'm interested to know if can I have the Zigbee protocol on the nRF5340 microcontroller and use a web browser (from my phone for example) and get a http page from the MCU...
