Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
hello,
I have downloaded the DTM firmware and connected it according to the serial port pins defined in the figure below,
The selection of GPIO pins are pin 18 for RX...
I am trying to use the nRF as an intermediary bootloader for another microcontroller. All that I need the nRF to do is accept a 64kB binary file from my computer (at the moment...
Hello,
I have been testing the " ble_app_multilink_central " example given with Nordic SDK * nRF5_SDK_16.0.0_98a08e2 *.
nRF52840_DK board is working as the multilink...
I am getting an error when trying to run nrfutil, any tips on how to fix this?
~ ᐅ pip3 install --user nrfutil Requirement already satisfied: nrfutil in ./.local/lib/python3...
Hi,
I am developing project using nrf52840 and currently developing using SDK 3.0. (Once I complete my feature I will update to SDK4.1).
I am using the light bulb firmware...
Hello I am trying to run a simple zephyr bluetooth sample using nrf Connect SDK v. 1.5.1 I am using your nRF5340 DK The sample I am running is: beacon I followed your instructions...
I have one TX and another RX codes for data communication by ESB protocol. To verify whether data whitening can be enabled, I added below register setting on TX side only...
Hi. I'm developing nRF52832.
I'm in the process of setting up BLE, but there's a problem.
There was a problem while I was organizing the files due to successful BLE communication...
Hi,
I can able to get the DEVADDR0 and DEVADDR1. I am not able to make out How this EUI64 id is calculated using the DEVADDDR value.
I always get F4CE36 starting numbers...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
Hi,
I'm working on a multilink central device with SDK16, nRF52832.
I'm trying to connect the central to 2 peripherals with certain address. So I added 2 address filters...
