We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello!
I am trying to set up automated tests for an application on the nRF54L15 BabbleSim target. The application needs two-way communication with a test script; this would...
hello
In the nrf/sample/net/aws_iot example, when updating a shadow topic, use $aws/things/<thing-name>/shadow/update/
Where does "thing-name" refer to?
Regards,
Dae...
Hi All,
We have an application that was compiled on nrf54L15DK where we get UART logs . The application was tested on DK and is working fine. Use Case:
Wanted to run...
I am interfacing the DS18B20 digital temperature sensor with the nRF52810 using the nRF5 SDK . The same firmware and hardware configuration works correctly on the nRF52832...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
Hello,
I am currently using the bt and uart backend for zephyr logging on ncs 2.9.2. I want to be able to save logs to flash which will be useful in debugging/ and be...
I am trying to establish a BLE connection between two nRF52840 devices.
The child devices are properly advertising and are close to each other.
When attempting a BLE connection...
Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
I saw a description about on-the-fly CCM mode decryption in the nRF54L10 datasheet, but the Configuration section of CCM00 states that it does not support on-the-fly decryption...
I would like to know about the Mesh model.
Light Lightness、
Light CTL、
Light HSL Setup、
Light Control
Are there no configuration components for any of the above...
Hey,
To program the nRF54L15 EVK, is there some dedicated program tool needed?
From EVK package ordered online, there is only USB cable inside. Can I assume the USB cable...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
I'm developing a solution using nrF54L15 that needs to receive packets from existing legacy RF devices in the field that cannot be modified.
Required RF Parameters:
...
Hi team,
I am using ncs2.6.1 ( github - install from VS Code ) , toolchain 3.0.2 ( previously used 2.6.1), My DK works great standalone also here is the view from nrf-connect...
