We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I am planning to get the PPK2 fabricated and assembled using the HW files available for PPK2.
Just wanted to check will I have issues loading FW on it since I don...
Hi all,
I’m working with an nRF52833 using SDK 2.8 and trying to enable DCDC mode to reduce current consumption.
I tried adding:
CONFIG_BOARD_ENABLE_DCDC=y but I got...
When developing a keyboard peripheral using the nRF5 SDK keyboard example, how can I determine whether the connected host device is a Mac, Windows PC, or Android phone?（NRF52833...
Hi, I am working on a channel sounding trilateration system using an initiator and three reflectors. When I was testing with six reflectors I couldn't help but notice the...
Hi all,
I need to use the SPI3M interface and following various example I implemented the following code on the nRF52840 with SDK 3.0.2
Whenever I configure the SPI to...
Hello - Just download and installed NRF Connect for Desktop 5.2.0 on Windows 10. Trying to Quick Connect to new PPK2 1.1.1.
When I plug in USB Quick Connect sees the PPK...
Hello,
we were using the mcumr_flutter 0.4.2 library to Update our NRF54L10 over the air with an app. This was working fine using the nRF Connect SDK Toolchain v2.9.0. However...
Hello,
I'd like to have the gcc linker calculate a checksum over a specific address range (defined in .ld file) and store that checksum at a specific address (defined...
example: peripheral nus device: nrf52832(Self-developed board) hi i run the example peripheral_nus , but it cannot work. Though i had set the RC clock. But when i run the...
Hi, I am developing a product that has a nRF52840 as the main MCU and it controls a Quectel BG95 (a LTE-M/NB-IoT module, powered by Qualcomm's 9205 LTE modem) using Zephyr...
Good Day,
Im a developer in switzerland using the nrf9160 trying to connect to the nrf cloud using mqtt, i have already flashed the credentials, updated the modems firmware...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi all,
In Device Manager, my nRF52840 DK is recognized as follows:
JLink CDC UART Port (COM32) JLink CDC UART Port (COM33) USB Serial Device (COM22) — running a Zephyr...
I'm looking to use the new Zephyr support for the ProMicro nRF52840 board, which appears to be available in NCS v3.
However, Zigbee R23 only appears to target v2.9.0.
...
Dear devzone support,
I have a quick quesiton.
Why does the nrf5340_audio application only support 1 BIG, while the nrf_auraconfig support 2 BIG. Is it because of using...
