But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Again no where I can find to put this. Also under documentation as a tag you need another option to select, e.g. SDK
Anyhow, When I try and search the documentation the...
I think I've found a bug in the power management that occurs only when a softdevice and the debug interface are active. In SDK v17.0.2, nrf_pwr_mgmt.c lines 417-429:
The...
Hi,
We using nRF Connect SDK,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/zigbee/lib_zigbee_shell.html#zigbee-shell-command-list
We founded...
Hello,
I am working on nrf52833 using the soft device s140 ble with csence enabled.
but the cap button has problems to detect signal, what is the
THRESHOLD_BUTTON...
Hi,
I'm using nRF5 SDK, use original build. No change anything. Just enable the Zigbee CLI as Coordinator.
After tested with various devices, found out a lot devices...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. Is there an upper limit to the number that can be stored...
Hi,
I am trying to configure a GPIO pin P0.21(as this is exposed pin on Thingy:91) from nRF9160 on Thingy:91.
I am using nRF Connect SDK 1.4.1 with Nordic version of SES...
Hi,
I am evaluating the LTE modem demo. I downloaded the demo binary firmware images a few weeks ago. Today I installed the LTE Modem demo into my dev kit. It connected...
I want to develop a 2.4G mouse Dongle and have used NRF52840 and SDK 17.0.2. When I have used USB or ESB one by one - all is Ok. But when they are used together - usb driver...
Hey all
I've been searching and trying all sorts of options for this but I'm stuck.
I'm currently working on a Thread sensor prototype on the 52840DK. I'm trying to...
There are two issues in one here. The easy fix is the check for overflow in format_offset_string_print() if (length <= p_cli->p_ctx->vt100_ctx.cons.terminal_wid - terminal_offset...
I have a bit of an odd one, and would appreciate any input. We have a fairly complex project, which does various things, but some of the time, I get a hardfault. The issue...
I am getting linker errors such as the following:
Output/Release/Obj/saadc_pca10056/nrf_sdh.o:SDK\components\softdevice\common/nrf_sdh.c:83: undefined reference to `start_sdh_req_observers...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
