But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello, we are currently migrating from nRF Connect v2.9.1 to v3.0.2. When doing so, we found that the tinycrypt API was deprecated and decided to move things to mbedtls. We...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
Hi
I am writng some peer information just after connection using pm_peer_data_store . I need to read the data stored to do the next task. As the FDS is asynchronous, i am...
When I run nrfutil toolchain-manager list I get output like the following:
The * indicates which toolchain version is currently active in my environment.
However, there...
We are just kicking off a new design with a nRF54L15. We would like to use the GRTC as a pseudo real-time-clock. We know that it retains its value through a reset and in system...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Hello Sir,
I am currently working with the chip :nRF54l15 and ncs:2.9.1
Now, I have designed an onboard PCB antenna using the nrf54l15 chip and flashed the peripheral_uart...
Hello, I'm trying to use BLE on nrf52833. I'm developping with segger embedded studio and I' m usign the BLE peripheral example "ble_app_blinky". Firstly I erased the flash...
Hello,
I downloaded the zip file "mfw_nrf9160_1.3.7.zip" from nordic and I am trying to upload it via the programmer tab in the nrf connect to desktop app, but I keep...
Hi
I have couple of questions,
GRTC work as RTC (Real Time Clock)?
If yes then why there are three dedicated pins? (P0.03,P0.04,P1.08) means we can use it at outside...
I've been trying to connect the LSM6DSO32 IMU to the nrf52840 via SPI, however the mcu is unable to detect the IMU no matter what I try. What are some ideas on how I can debug...
Hi,
I am using ncs v2.6.1 SDK.
I'm trying to use a nrf52833 central to connect 15 peripheral, t he connection distance is about 6 to 7 meters, and the connection environment...
I am using the nrf5340 with the nrf7002 as the companion Wi-Fi IC. The supply voltage to all my peripherals (3V4) is enabled when my device exits sleep (System On + Idle)...
