This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I want to use a UART line to send and receive data to a nrf52840 DK and then have the data sent wirelessly to a separate DK and then print it to a terminal like in the multi_sensor...
Hello,
currently am working on connecting two different modules of BLE, nrf51822 and Rn4871.
The problem am facing is that i am not able to send and receive data between...
Hi,
We are using mesh SDK 5.0 on NRF52840 integrated with PIR and light level sensors for office lighting, it works well.
Now we'd like to check if we can expand the system...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
I see this line for cache enable register in application domain : infocenter.nordicsemi.com/index.jsp
NVMC built-in cache not supported (ICACHECNF, IHIT and IMISS registers...
I'm trying to test button less dfu on nrf 52840 dk. i am simply compile that hex ble_app_buttonless_dfu_without_bonds_s140_with_setting_page.h file with soft device s140 or...
I am building the coded bluetooth gateway using nrf52840 and ENC28J60. Integrated between two examples:
https://github.com/nrfconnect/sdk-nrf/tree/master/samples/bluetooth...
Hi to everyone!
I am working (with Keil uVision) on a custom PCB that includes the NRF52832 (MDBT42Q module) and some sensors from MAXIM INTEGRATED. There is a Sensor Hub...
Hello, I was told to make a new ticket after commenting on this ticket .
I am using SDK 14.2, S140 alpha, NRF52840. Segger IDE. I have been developing with this IDE & SDK...
