Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
Hello,
While I am creating a new projects. I am getting an error message. I don't know the path of the files . I randomly created a project in D drive ,c Drive . So My question...
There are the following projects under the Health Thermometer example for Keil
What is the difference between them when trying to install on the nRF51 DK? I could not find...
Two (2) nRF52840 DKs, SDK 17.0.2
I believe I have added the necessary code from ble_blinky_apps both peripheral and central to their respective NFC reference role examples...
Dear Sir/Madam,
I'am new to segger embedded studio.I would like to do SPI interfacing of an IC using nRF51822 with segger embedded studio.
Please guide me how to add...
Zephyr version: 2.4.99
OS: Linux
Board : nrf9160dk
I am trying to read data on UART 1 with interrupt. I have below shown portion in my code for enabling UART 1. (I...
Hi, I need to Interface the 2.4" SPI TFT Module ILI9341 Driver with nRF52832
I came across that in Peripheral/ GFx Example will run. once I build and run the project My...
Hi Dev Team,
I was working on the Nordic Thingy91 and had to establish an external communication of a sensor to the Thingy91 through a UART.
For this, I was looking into...
Hi,
My PC is Windows 7 64-bit and my tool is J-Link V9. The CPU at my target board is nrf52840. I use nRF connect desktop version 3.60 and it works fine. I got the upgrade...
I have the driver setup like all of the other sensor drivers I'm using, but I can't seem to find a device tree or Kconfig
This should be enabled by the CONFIG_SOC_NRF52840_QIAA...
Hello!
We have a custom board connected to a battery and a USB cable
Our fw calls:
NRF_POWER -> SYSTEMOFF = 1 ;
The board turns off.
And then we remove the USB...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
