But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
Hi,
I use the SAADC with the NRF52832.
This is the schematic used :
When we use AN_IN (TOR_IN 1 and TOR_IN 2 are not used), only the components assigned to AN_IN are...
File nrf_pwr_mgmt.h is lacking
#ifdef __cplusplus extern "C" { #endif
magic.
SDK version: nRF5_SDK_15.3.0_59ac345.zip
I guess it is a small oversight since all other...
Hi using nrf52 SDK 15.1, on custom boards
I have certain flash operations using FDS. I have peer manager as well.
I am writing 8 byte data & later in the code updating...
I am attempting to develop an application for a custom board with the nRF52832. I am attempting to use the UART functions in the SDK but I am running into compile errors....
Hi, I am trying to fix a crash in the dfu service. I am using a custom board based on the NR52840, SDK 15.0 and softdevice 6.0.
I am trying to add some new characteristics...
I would like to run a SPI program that reads data from a non Nordic chip. I would like to then take the data I received over SPI and send it via BLE.
Are there any code...
I'm trying to place my device in a low power mode for shipping. I used Logging and CLI while its in operation, but I'd like a way to enable/disable the CLI+Logging over BLE...
I'm testing a simple program below, which writes three params followed by read the three params.
Each params is set in tx_buf correctly, but nvs_write does not seem to work...
I am developing a hand-arm vibration sensor for read-out via BLE
Development platform NRF51822 and S110
I'd like advice on how to configure the softdevice and the two...
Nrf52832 sdk15.2 is debugged online after burning softdevice, bootloader and bootloader settings. In the ble_dfu_buttonless_async_svci_init() function, the error NRF_ERROR_SVC_HANDLER_MISSING...
