But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
I'm trying to set up an ESB PRX on an nRF52 that has to communicate with an nRF24L01 chip acting as PTX. Because I want to react to the received data as quickly as possible...
Hello,
I am trying to use Softdevice and the latest Github version of 802.15.4 support. The make (using linux/armgcc) fails on
nrf_raal_softdevice.c
because nrf_802154_radio_irq_handler...
Using SDK 15.2 on an nRF52832 using SoftDevice S132. FDS works OK unless the SoftDevice is enabled. None of the examples work. We've tried the peripheral example, GitHub examples...
Hi,
I'am testing direct advertise and I found strange behaviour with "nrf connect" app.
1. Direct advertises won't be proceeded on "nrf connect" unless there is at least...
Hello everyone
I got back on my bluetooth mesh project after an interruption and at the time I remember having the same compilation problems solved so far.
I worked with...
Hi all,
I acquired the wonderful nRF9160 DevKit which embeds the ARM CryptoCell 310.
Rather than using the mbedTLS or TinyCrypt libs, I would like to rely on the CC310...
hi....
i am just started to program the mesh , i am getting the error in my example code , how to solve ? this is the latest version of 3.1
boards.h: No such file or ...
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for developing the nRF Mesh.
I am using segger IDE for programming but I am looking for a way to program the device with hex...
Hi
In MESH 3.10 SDK，i want to configure and use virtual address, but i can't add the virtual address in both pulication address/subscription address when i use NRF Mesh...
Hi Sir,
Normally, the printf() may show the message to UART_0, is there any way we can re-direct the message of printf() to UART_1?
in other words, can we choose the...
I am facing issues in debugging ble_app_uart program available in nRF5 SDK. I am trying to debug it on IAR workbench using Jlink PLUS debugger in SWD mode.
I could connect...
Hi Nordic support team,
I used mergehex to merge the hex files of Softdevice, Secure Bootloader (nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble) and...
